How Air-Source Heat Pumps Work: COP, SCOP, and HSPF2 Explained
Air-source heat pumps move existing thermal energy rather than burning fuel, allowing them to deliver multiple units of heat for every unit of electricity consumed. This guide breaks down the refrigeration cycle alongside COP, SCOP, and HSPF2 ratings with worked US, UK, and EU cost examples.
Updated 2026-11-19 · 1635 words
Heat Movement vs. Heat Creation: The Vapor-Compression Cycle
Every combustion furnace, electric baseboard heater, and gas boiler generates thermal energy by converting chemical or electrical potential directly into heat. An electric resistance coil is locked at 100% thermal efficiency at the point of use because one kilowatt-hour (kWh) of electricity can produce at most 1 kWh (3,412 BTU) of heat. An air-source heat pump operates on a fundamentally different thermodynamic principle: it uses electricity not to create heat, but to power a compressor and fans that absorb ambient thermal energy from outdoor air and concentrate it indoors.
Even when outdoor air feels frigid at 14°F (-10°C), it still contains substantial thermal energy relative to absolute zero (-459.67°F or -273.15°C). Inside an air-source heat pump, a closed loop of refrigerant—commonly R-32, R-454B, or R-290 (propane) in newer residential units—circulates through four core components:
- Outdoor Evaporator Coil: Liquid refrigerant enters at low pressure and a temperature colder than the outside air. Outdoor air blown across the fins boils the refrigerant into a low-pressure gas, absorbing ambient heat.
- Inverter-Driven Compressor: An electrically powered compressor squeezes the vapor, sharply raising both its pressure and temperature (often above 140°F or 60°C) in accordance with the ideal gas law.
- Indoor Condenser (or Plate Heat Exchanger): The hot, high-pressure gas releases its heat into indoor air (in an air-to-air system) or into hydronic radiator/underfloor water (in an air-to-water system), condensing back into a high-pressure liquid.
- Electronic Expansion Valve (EEV): The liquid passes through a narrow metering orifice that drops its pressure and temperature, resetting it to absorb more outdoor heat on the next pass.
A four-way reversing valve lets air-to-air heat pumps flip this cycle in summer, turning the indoor coil into the evaporator and rejecting household heat outdoors just like a central air conditioner.
Instantaneous COP: What a Snapshot Number Actually Measures
The fundamental building block of heat pump efficiency is the Coefficient of Performance (COP). COP is a dimensionless ratio comparing useful thermal output to electrical input at a single, precisely controlled operating point:
COP = Thermal Heat Output (kW or BTU/hr) ÷ Electrical Power Input (kW or BTU/hr equivalent)
If a heat pump draws 1.5 kW of electricity from your breaker panel while delivering 5.25 kW (17,913 BTU/hr) of heat into your living room, its instantaneous COP is 3.5. That means 71.4% of the delivered warmth came free from the outdoor air, and only 28.6% came from purchased electricity.
However, COP is never static. Thermodynamics dictates that efficiency shrinks as the temperature lift—the gap between the outdoor source temperature and the indoor delivery temperature—widens. In a cold-climate air-to-air unit tested under AHRI 210/240 conditions, a machine might post a COP of 4.1 at 47°F (8.3°C) outdoor air, drop to a COP of 2.6 at 17°F (-8.3°C), and fall to 1.8 at 5°F (-15°C). For air-to-water systems serving UK or European hydronic radiators, the indoor water flow temperature matters just as much as the weather. Running radiators at 95°F (35°C) underfloor temperatures typically yields a COP roughly 0.8 to 1.2 points higher than pushing 131°F (55°C) water through undersized legacy radiators.
Seasonal Metrics Compared: SCOP (EU/UK) vs. HSPF2 (US)
Because a single COP rating at mild spring temperatures can make mediocre equipment look extraordinary, regulators rely on seasonal metrics that weight performance across an entire winter's temperature distribution.
SCOP (Seasonal Coefficient of Performance)
Across the United Kingdom and the European Union, air-source heat pumps are rated under European Standard EN 14825 using SCOP. Rather than testing at one temperature, manufacturers measure capacity and power draw across multiple outdoor temperature bins and calculate a weighted seasonal average. EN 14825 defines three reference climate profiles: Warmer (Athens-like), Average (Strasbourg-like, which serves as the standard baseline across most of Western Europe and the UK), and Colder (Helsinki-like). A heat pump with an Average-climate SCOP of 4.2 at 35°C flow temperature delivers 4.2 kWh of heat per 1 kWh of electricity over a typical heating season—including standby power and supplementary backup logic.
HSPF2 (Heating Seasonal Performance Factor 2)
In the United States and Canada, ducted and ductless air-to-air heat pumps use HSPF2, introduced by the U.S. Department of Energy in January 2023 under the M1 testing procedure. HSPF2 is the ratio of total seasonal heating output in BTU divided by total seasonal electrical input in watt-hours (Wh). Because 1 watt-hour equals 3.412 BTU, you can convert HSPF2 directly into a US-equivalent seasonal COP by dividing by 3.412:
Approximate Seasonal COP = HSPF2 ÷ 3.412
The 2023 transition from legacy HSPF to HSPF2 raised the external static pressure test requirement for ducted split systems from 0.10 to 0.50 inches of water column, reflecting the real-world drag of household ductwork and filters. As a result, a unit's HSPF2 number is roughly 15% lower than its older HSPF label—even when the physical hardware has not changed.
| Metric | Primary Region | Units / Expression | Typical Good Residential Range | What It Captures |
|---|---|---|---|---|
| COP | Global (Lab & Spec Sheets) | Dimensionless ratio (kW/kW) | 2.5 – 4.8 (at 47°F / 8°C) | Instantaneous efficiency at one fixed outdoor and indoor temperature |
| SCOP | UK & European Union | Dimensionless ratio (kWh/kWh) | 3.4 – 4.6 (Average climate) | Full-season weighted heating efficiency under EN 14825 |
| HSPF2 | United States & Canada | BTU ÷ Watt-hours | 7.5 – 10.5 (Split systems) | Full-season heating output per Wh under higher M1 duct static pressure |
| Equivalent COP from HSPF2 | US Conversion | HSPF2 ÷ 3.412 | 2.2 – 3.1 (Standard) / 2.8+ (Cold Climate) | Allows direct comparison between US HSPF2 and EU/UK SCOP |
| SEER2 | United States & Canada | BTU cooling ÷ Watt-hours | 14.3 – 22.0 | Seasonal cooling efficiency under M1 testing |
Worked Numerical Walkthroughs: US, UK, and EU
Translating seasonal ratings into household utility budgets requires matching the equipment's seasonal efficiency against your annual heating load and local electricity tariff. Below are three worked examples illustrating how the math plays out across different regions. Actual household bills will vary with thermostat habits, envelope airtightness, and tariff changes.
1. United States Example ($ / BTU / °F)
Suppose a 2,100 sq ft home in Ohio has an annual space-heating demand of 52,000,000 BTU (52 MMBTU) across a winter where temperatures frequently dip between 15°F and 40°F. The homeowner evaluates a cold-climate ducted heat pump rated at 9.5 HSPF2, paying an all-in residential electricity rate of $0.16 per kWh.
- Step 1 — Convert HSPF2 to seasonal COP: 9.5 ÷ 3.412 = 2.78 seasonal COP.
- Step 2 — Calculate annual electricity consumption: Divide total BTU by HSPF2 to get watt-hours: 52,000,000 BTU ÷ 9.5 = 5,473,684 Wh, or 5,474 kWh.
- Step 3 — Estimate seasonal heating cost: 5,474 kWh × $0.16/kWh = $875.84 per winter.
By comparison, pure electric resistance heat (COP 1.0, or 3.412 HSPF2) for the same 52 MMBTU load would consume 15,240 kWh and cost $2,438.40—meaning the heat pump reduces heating electricity use by roughly 64%.
2. United Kingdom Example (£ / kW / °C)
Consider a 1990s three-bedroom semi-detached house in the Midlands with an annual space-heating requirement of 11,500 kWh. The homeowner installs an air-to-water monobloc heat pump paired with upgraded low-temperature radiators designed for a 45°C maximum flow temperature at -3°C outside, achieving a verified SCOP of 3.7. Electricity costs £0.24 per kWh on a standard tariff (or £0.15/kWh on an off-peak heat pump tariff, though we will use £0.24/kWh as a conservative baseline).
- Step 1 — Calculate annual electricity consumption: 11,500 kWh thermal ÷ 3.7 SCOP = 3,108 kWh electrical.
- Step 2 — Estimate annual heating cost: 3,108 kWh × £0.24/kWh = £745.92 per year.
If the installer failed to upgrade undersized radiators and forced the system to run at 55°C flow temperature, dropping real-world SCOP from 3.7 to 2.8, electrical demand would jump to 4,107 kWh (£985.68)—an avoidable £239.76 annual penalty driven entirely by emitter sizing.
3. European Union Example (€ / kW / °C)
A well-insulated 135 m² home near Munich requires 9,800 kWh of annual space heating. A modern R-290 air-to-water heat pump feeding underfloor heating loops at 35°C achieves a seasonal SCOP of 4.4. With a German residential heat pump electricity tariff of €0.29 per kWh:
- Step 1 — Calculate annual electricity consumption: 9,800 kWh ÷ 4.4 SCOP = 2,227 kWh.
- Step 2 — Estimate annual heating cost: 2,227 kWh × €0.29/kWh = €645.83 per year.
Why Real-World Field Performance Can Differ from Lab Ratings
Even the highest SCOP or HSPF2 badge is only a laboratory benchmark. Three operational factors commonly separate nameplate ratings from actual meter readings:
Defrost Cycles
When outdoor temperatures sit between 28°F and 42°F (-2°C and +6°C) during damp, foggy weather, moisture in the air condenses and freezes onto the outdoor coil. Left unchecked, frost blocks airflow and starves the evaporator. To clear it, the heat pump briefly reverses operation for 3 to 6 minutes, drawing warmth from indoors (or activating a small electric element) to melt the ice. Frequent defrosting in maritime climates like the UK, Pacific Northwest, or Northern Germany can trim effective seasonal efficiency by 5% to 10%.
Auxiliary Electric Resistance Strip Heat
Many North American ducted heat pumps include 5 kW to 15 kW electric resistance backup coils inside the air handler. If an aggressive thermostat schedule jumps 5°F (3°C) upward on a cold morning, the thermostat may energize the backup strips (COP 1.0) to recover quickly, wiping out hours of efficient heat pump operation. Modern inverter heat pumps work best with steady temperatures or gentle 1°F–2°F (0.5°C–1°C) setbacks.
Weather Compensation and Flow Temperature Control
In hydronic systems, running a heat pump at a fixed 50°C water temperature all winter wastes energy during mild autumn and spring weeks. Weather compensation curves automatically lower the water flow temperature—perhaps to 30°C when it is 12°C outside—keeping the compressor in its highest-COP sweet spot for most of the year.
Pre-Purchase Homeowner Checklist
- Verify whether quoted efficiency numbers are HSPF2 (not legacy HSPF) in North America, or SCOP at your actual design flow temperature (35°C vs. 55°C) in the UK and EU.
- Ask your installer for a room-by-room heat loss calculation (Manual J in the US, MCS/EN 12831 in the UK and Europe) rather than a square-footage guess.
- Confirm the minimum modulation capacity of the compressor so the unit does not short-cycle during mild 45°F–55°F (7°C–13°C) shoulder-season weather.
- Inspect existing ductwork static pressure or radiator surface area to ensure low-temperature delivery without excessive fan or pump power.
- Check local utility time-of-use or dedicated heat-pump tariffs before finalizing your operating cost budget.
Technical & Safety Notice: Air-source heat pump installations involve high-voltage electrical circuits, pressurized refrigerants, and building envelope penetrations that must be sized, brazed, evacuated, and commissioned by licensed HVAC technicians and certified electricians in compliance with local codes. Efficiency projections in this guide are educational estimates based on standard test protocols and cannot guarantee specific utility bill savings.